How To Add Extra Pockets For Tools On The Backpack

Want to take your rucksack game to the next level so you can effortlessly carry additional tools? Improving your go-to backpack with additional tool compartments may be a game-changer. How your life would be if you didn’t have to worry about fitting everything into that one overflowing bag anymore? Want to know how to add extra pockets for tools on the backpack?

Whether you’re a professional navigating the urban jungle or a weekend warrior out on a trek, having more pockets allows you to pack more effectively and carry all those must-have essentials without feeling bogged down. It’s like arming your tool bag with superpowers; now you can take extra stuff on all your excursions.

You won’t have to compromise on room for snacks or your beloved multitool anymore. Everything you need will be easily accessible thanks to the extra pockets carefully placed on your backpack. Take things into your own hands and personalize your backpack to fit your demands properly if you’re weary of carrying about a large toolbox or always searching through an unorganized bag by reading this blog:

Steps To Add Extra Pockets For Tools On The Backpack:

Following are the important steps on how to add extra pockets for tools on the backpack.

Step 1: Take Apart Your Backpack:

Get a good look at your rucksack and mark its primary components. Sections one, two, and three were available to me. First, you’ll need to remove the bias tape that covers the seam with a seam ripper. The three pieces may be seam-ripped apart when the bias tape has been removed. Caution should be used while disassembling; for instance, the front pocket and straps were superfluous.

Step 2: Make Your Laptop Compartment:

You must first determine the proper orientation of your laptop inside the bag. You may want to try orienting your laptop vertically instead because many larger computers won’t fit inside your bag while sitting horizontally (my Dell XPS 13 fits nicely). Adapting your dimensions to fit will be necessary in such circumstances.

Keep on by taking the dimensions of your laptop. A 12-inch-long, 8-inch-wide, and half-inch-tall laptop was my possession. Make sure the width of your backpack is the same as your laptop’s length when cutting the interfacing piece; if your laptop is vertically oriented, the width should be the same as the length.

Consider the height of your laptop, add 0.75 inches of seam allowance along the three not-folded sides, and double the length of the interfacing to get the fabric measured. The interfacing will be covered on both sides by the fabric.

I hope these calculations make it easier for my math-savvy friends to determine the dimensions of the cloth that is about to be folded—

The formula for fabric width is widthInterfacing plus two times the height of the laptop plus two times the seam allowance. “Height + 2 times the length of the interface surface + seam allowance“. Source…

Finally, press the fabric length so it covers both sides of the interfacing, fold it over so it covers the interfacing as well, and stitch along the unfolded sides to secure the interfacing.

Step 3: Make The Removeable Pencil Pouch:

Pick out two different fabrics—one for the inside and one for the outside—and use pinking shears to cut out two rectangles of each. With a half-inch margin on all sides for seam allowance, I cut rectangles that were 10 by 7 inches.

One of the pouch’s outside sections may be embellished with embroidery if you so want. I used a washable marker to draw a pattern, and then I stitched it using a backstitch.

The tabs for the magnetic snaps need to be made before the bag can be sewn together. Make three-by-three-square cuts, fold in half, and stitch along one side. Make a half-inch fold in the tops and stitch them down. Finally, turn the tabs over on their backside. When you’re ready to reassemble the bag, set aside two tabs.

Layer the rectangles with the longer zip side down, then sew them onto the tough and soft fabrics, two tabs, and so forth. Be cautious not to stitch over the tines as you sew along the zipper. After that, stitch the other side after layering the zipper, soft fabric, and strong fabric (but without tabs). Finally, unzip the zip and stitch along the three edges that have not been sewn. After you turn it inside out and attach the magnetic snaps, you’re good to go.

Step 4: Make The Water Carrier:

To make the elastic, measure the circumference of your backpack and add half an inch to each side for seam allowance; my measurement was 8 inches. The recommended length of the mesh is two inches longer, which works out to ten inches for me. I measured 8 inches for the mesh width, which is the measurement from the zipper pull to the bottom of the backpack, plus an additional inch for seam allowance.

Further equations, for the sake of clarity: Elastic length equals the center of a backpack plus two times the sewing allowance.

MeasureMesh = measureElastic + 2 in. The breadth of the mesh is equal to the zipper’s bottom plus two times the seam allowance.

Attach one end of the elastic to the mesh by matching it to a side that is two inches longer than it. Next, pin the elastic in place after stretching it to meet the mesh’s end. To make the elastic seem to lay flat along the mesh, use a stretch stitch to sew it into place.

If your backpack has a seam running down its length, you may just insert the mesh pocket’s bottom and put it back together. Otherwise, you’ll need to stitch the bottom of the mesh pocket straight into the central portion of your bag. To prevent fraying, roll the bottom edge of the mesh pocket twice before sewing it onto the ‘bottom edge’ of your backpack, which is the point where the side touches the ground. Secure the top with pins and save it for later when you’re sewing the backpack as a complete.

Step 5: Make The Glasses Pocket:

Although I intend to use it to retain my spectacles, this bag has a wide variety of potential uses, such as a clutch for keys, cards, cash, jewelry, and more. Choosing a delicate lining fabric for the interior is my recommendation for glasses, but it may not be required for keeping less fragile goods.

What you want to put in the pocket should be measured. Be sure to include 1.5 inches for seam allowance and double the length of the tough and soft fabrics to match the object(s) you’re making. In addition to the 1.5-inch seam allowance, the width of your rucksack should be measured from the edge or rear to the zipper.

Before cutting off any extra, stitch the zipper to the outside and inner fabrics. If the zipper is longer than the area you need to fill, sew across it at the desired endpoint. Assemble the backpack by sewing the other side of the zipper onto the top edge, positioning the pocket in the exact center of the middle part.

The exterior of the bag will reveal these stitches, therefore it’s important that they are straight and that the thread color matches. After you’ve folded over the two sides of the 1-inch seam allowance to hide the raw edges, pin the remaining portion of the pocket into place. Put the two halves of the bag into the backpack with care, allowing the other halves to be stitched together later.

Step 6: Sew the Backpack Together:

Position the laptop pocket with the correct side facing down, and then place the rear of the backpack on top of it, strap side up. Pin the pocket to the bottom of the bag section, being careful to provide enough room for the laptop’s height around the corners. Pin the tabs of the pencil pouch to the top of the bag, just above the seam, at an equal distance from each other.

This will serve as the “outside” of the seam. Lastly, with the incorrect side facing out, pin down the centerpiece of the bag. In the same spot as the initial seam, sew around the backpack. Pick the line that is farthest from the center if there are two lines of holes.

Invert the two halves that have been sewn together, so the incorrect side of the center part is facing out. Carefully reattach the front piece by opening the zipper and sewing it in place. After sewing the two seams, return the bias tape to its original position along the innermost line of holes. Your rucksack should now be more practical and interesting.

Conclusion:

Follow our guide on how to add extra pockets for tools on a backpack if you want to improve your carrying experience. If you follow the instructions in this article, you can turn any old backpack into a multipurpose toolbox. With thoughtfully arranged pockets, you’ll never again have to rummage through a jumble of belongings or lose useful equipment.

So, don’t be shy about personalizing your rucksack to suit your needs, whether you’re an outdoor explorer, DIY enthusiast, or someone who just values organization. If you’re willing to put up the time and effort, along with some simple supplies, you may create a rucksack that is perfect for you and your adventures.

Get ready to level up your backpack game by adding those additional pockets! Bid farewell to clutter and welcome to convenience!